Haier Flat Panel Television L15D2 A0 User Manual

15"17"20"LCD TV  
USER'S MANUAL  
MODEL:  
L15SV6-A0, L17LV6-A1,L20AV6-A0  
L17L6A-G1,L20L6A,L15G1-A0,  
L17G1-A0,L20G1-A0,L15D2-A0,  
L17D2-A0  
Please read this manual carefully before  
using your television and keep this manual  
In a good place for future reference.  
 
Safety Notice Items  
Incorrect usage will cause fire or electric shock. To prevent this, please do  
as required when you are installing, using and cleaning this machine. To insure  
your safety and extend the life-span of LCD-TV, please read the following items  
carefully before using:  
l Please read and understand all the instructions before operation;  
l Please keep the book for later use;  
l Please comply with the warning instructions on the machine and in this book  
strictly;  
l Please comply with the instructions provided;  
l Please do not use additional devices that are not recommended by  
manufacturer:  
l Before operation, please make sure that the operating voltage of your unit is  
normal;  
l Do not placethe unit onunstable, dusty andhumid places;  
l Never put theunit in directsunlight or nearheat sources;  
l Allow enough space for proper ventilation;  
l Please keep water away from the LCD-TV . If water comes in contact with the  
LCD-TV, disconnect the power cord from the power source, then wipe the set  
with a dry soft cloth;  
l Do not remove the back cover. If services were need, please refer to qualified  
Personnel  
Main Functions  
1-Can be connected with analog RGB input  
2-Can be connected with CVBS,S-VIDEO , and SCART (CVBS/RGB)  
input  
3-Can receive TV signal  
 
Front Panel Controls  
7
6
7
6
5
1
2
3
4
5
1
2
3
4
6
6
7
MENU  
PR  
VOL  
TV/AV  
1
3
5 7  
2
4
3
2
4
G1 series  
1
D2 series  
1
4
2
3
5
4
2
3
5
TV/AV MENU VOL- VOL+ CH-  
CH+ POWER  
TV/AV MENU VOL- VOL+ CH-  
CH+ POWER  
7
6
7
6
Note: These buttons are onthe top ofthe sets onthese two series.  
Control Panel Function  
1. MENU Press to select the main menu  
2.  
VOL (V-/VOL-) Volume down /Left orientation toadjust the itemin the OSD  
VOL (V+/VOL+) Volume up / Right orientationto adjust theitem/Press to  
enter the submenu.  
3. PR (P-/CH-)  
TV channel down / to select the item in the menu  
TV channel up / to select the item in the menu  
Select the inputsignals: SCART/PC-RGB/AV/S-VIDEO/TV  
PR  
4.TV/AV  
(P+/CH+)  
5. Power supplyswitch  
6. Power indicator  
Illuminates red in standby mode, illuminates green when the display is  
turned on  
7.Remote Sensor  
Receivingremote control sendsthe infrared remote  
signal.  
 
Connection Options  
The figure is just for referrence, please see the real.)  
AV Audio Input  
D-SUB Input  
Connect audio/video  
output from an external  
device to these jacks  
SCART Input  
Connect to the D-SUB  
15PIN analog output  
connector of the PC  
display card for PC  
display purpose  
Connect to the DVD/  
VCR/broadcasting  
receiver or other  
equipment  
Earphone port  
L
R
DC IN  
D-SUB IN  
HEADPHONE PC AUDIO IN  
SCART  
S-VIDEO VIDEO  
AUDIO  
ANT  
S-Video Input  
PC Audio Input  
Connect S-Video out  
from an S-Video device  
to the jacks.  
Connect the PC output  
connector from a PC to  
the audio input port  
Antenna Input  
Connect cable or  
antenna signals to  
the TV, either direc-  
tly or through your  
cable box.  
DC Power Cord Socket  
This TV operates on DC power.  
The voltage is indicated on the  
Specifications page . Never  
attempt to operate the TV on AC  
power.  
 
Remote Control Key Functions  
When using the remote control, aim it towards the remote sensor on the TV  
SLEEP DISPLAY MUTE POWER  
NICAM  
PC  
AUTO AD TV/AV  
PSM  
OK  
.SSM  
Q.VIEW  
P+  
V-  
MENU  
V+  
P-  
INDEX  
TEXT  
SUBCODE MIX  
TIME  
HOLD  
SIZE  
REVEAL  
Illustration of the keys on the remote control:  
POWER  
1.  
Power supply switch  
MUTE  
2. MUTE  
3. DISPLAY  
4. 0-9  
Display current input signal information  
TV channel number select  
Set time to change the TV into the standby status after a  
period of preset time.(time is 240/180/120/90/60/45/30/15/0)  
5. SLEEP  
NICAM/A2 Stereo select  
EXIT  
6. NICAM  
7. OK  
Quick TV channel switch(return to the last channel)  
8.Q.VIEW  
9. V-  
Volume down / Left orientation to adjust the item in the OSD  
Volume up / Right orientation to adjust the item/Press to  
enter the submenu.  
V+  
TV channel up/down or select the item of the menu  
Select SCART/PC-RGB/AV/S-VIDEO/TV  
10. P+/P-  
11. TV/AV  
12. PSM  
Select picture mode: PERSONAL/STANDARD/MILD/FRESH  
 
Remote Control Key Functions  
PC-RGB system select  
13. PC  
M
Select sound mode:VOICE/MUSIC/THEATRE/PERSONAL  
Auto adjust (PC mode)  
14. SS  
28. AUTO AD  
15. RED  
Correspond to the differently colored subjects  
16. CYAN  
17. GREEN  
T
E
L
E
T
E
X
T
18.YELLOW  
19. TEXT  
Switch to the Teletext with text mode/turn off Teletext and  
switch to TV mode  
Hold on or off for current page display  
Switch to the Teletext with mix mode  
20. HOLD  
21. MIX  
Request index page  
Change display size  
22.INDEX  
23.SIZE  
Sub coded page access  
24.SUBCODE  
25.TIME  
While in normal TV mode only, pressing the button TIME will  
display the teletext time in the top right corner for a few  
seconds.  
Reveal or hidden the hidden words  
Press to select the main menu  
26.REVEAL  
27. MENU  
Note:  
The buttons instructionfor the operationjust take remotecontroller for examplein this  
manual . Buttons(MENU , V+/-or VOL or VOL+/-, P+/-or PR orCH+/-,  
TV/AV,POWER or )on the TV panel iscorresponding with buttons( MENU, V+/-, P+/- ,  
TV/AV , POWER )on the remotecontroller.  
Installing Batteries  
1.Slide open thecover of thebattery compartment onthe back ofthe remote  
control.  
2.Load two 5#alkaline batteries inthe compartment. (plusand minus polesto  
respective mark)  
3.Replace the coverof the batterycompartment.  
1
2
3
 
Connection Instructions  
Grounding  
Ensure that you connect the grounding / earth wire to prevent possible  
electric shock. If grounding methods are not possible, have a qualified  
electrician install a separate circuit breaker. Do not try to ground the  
unit by connectingit to telephone wires, lighteningrods, or gaspipes.  
External Equipment Connections  
Antenna Connection  
- Antenna or Cable Service with a Cable Box Connections  
- For optimum picture quality, adjust antenna direction if needed.  
Multi-family Dwellings/Apartments  
(Connect to wall antenna socket)  
wall antenna  
socket  
RF coaxial wire (75 ohm)  
VHF antenna  
UHF antenna  
Be careful not to bend the bronze  
wire when connecting the antenna.  
outdoor  
antenna  
Single-family Dwellings /Houses  
(Connect to wall jack for outdoor antenna)  
To improve picture quality in a poor  
signal area, purchase and install a  
signal amplifier.  
If the antenna needs to be split for two  
TV s, install a 2-Way Signal Splitter  
in the connections.  
If the antenna is not installed properly,  
contact your dealer for assistance.  
NOTE: All cables shown are not included with the TV  
 
Connection Instructions  
PC Setup  
You can use your LCD-TV as a monitor for your personal computer using a VGA  
cable (not supplied).  
Connection and use steps:  
1.Read the userguide supplied with  
your computer and ensure that it has  
a VGAconnector;  
2.Make sure that the power of the LCD  
-TV and thePC are off;  
3.Connect a Dtype 15-pin VGAinterface  
cable ( not supplied ) to the VGAvideo  
interface connector on the PC. Then  
connect the other end to the VGA video  
interface connector on the back of the  
LCD-TV.Tighten the screwson the VGA  
connectors once they are firmly  
connected;  
4.Turn on the power ofthe LCD-TV first,  
and then turn on the power of the PC;  
5.Press the TV/AV button to set the video  
input mode ofthe LCD-TV toPC-RGB;  
6.Check the image on your TV. There may be noise associated with the resolution,  
vertical pattern, contrast or brightness in PC mode. If noise is present, change  
the PC mode to another resolution, change the refresh rate to another rate or  
adjust the brightness and contrast on the menu until the picture is clear. If the  
refresh rate of the PC graphic card can not be changed,change the PC graphic  
card or consult the manufacturer of the PC graphic card.  
 
Connection Instructions  
VCR Setup  
- To avoid picture noise (interference), leave an adequate distance between the  
VCR and TV  
Connection and use steps:  
1.Read the user guide supplied with your AV devices and ensure that it has  
Composite or S-Video connectors;  
2.Make sure that the power of the LCD-TV and the AV device are off;  
Connection Option 1  
Set VCR output switch to 3 or 4 and then  
tune TV to the same channel number.  
Connection Option 2  
1. Connect the audio and video cables from  
the VCR's output jacks to the TV input jacks,  
as shown in the figure.  
When connecting the TV to VCR, match  
the jack colors (Video = yellow,Audio  
Left = white,and Audio Right = red).  
If you connect an S-VIDEO output from  
2
VCR to the S-VIDEO input, the picture  
quality is improved; compared to conne-  
1
.
cting a regular VCR to the Video input.  
2. Insert a video tape into the VCR and press  
PLAY on the VCR. (Refer to the VCR owner  
manual.)  
s
VCR  
3.Turn on the power of the LCD-TV first ;  
and then turn on the power of the AV  
device;  
4.Press the TV/AV button to set the video  
input mode of the LCD-TV to S-VIDEO  
mode or AV mode.  
 
Connection Instructions  
Cable TV Setup  
- After subscribing to a cable TV service from a local provider you can watch cable  
TV programming. The TV cannot display TV programming unless a TV tuner  
device or cableTV converter box is connectedto the TV.  
- For furtherinformation regarding cableTV service, contact your localcable TV  
service provider(s).  
Connection Option 1  
1. Select 3or 4 withchannel switch oncable  
box.  
2. Tunethe TV channel to thesame selected  
output channel oncable box.  
3. Select channelsat the cablebox or with  
the cable boxremote control.  
Connection Option 2  
1. Connect theaudio and videocables from  
the Cable Box'soutput jacks tothe TV  
input jacks, asshown in thefigure.When  
connecting the TV to aCable Box, match  
the jack colors  
(Video = yellow, Audio Left =white, and  
Audio Right= red).  
2. Select theinput source byusing the TV/AV  
button on theremote control.  
3. Select yourdesired channel withthe  
remote control forcable box.  
External AV Source Setup  
How to connect  
Connect the audioand video cablesfrom  
the external equipment'soutput jacks tothe  
TV input jacks, as shown inthe figure.  
When connecting theTV to external equip-  
ment, match thejack colors (Video = yellow,  
Audio Left =white, andAudio Right =red).  
How to use  
1. Select theinput source byusing the TV/AV  
button on theremote control.  
2. Operate thecorresponding external equi-  
pment. Refer toexternal equipment ope-  
rating guide.  
 
Basic Operating Instructions  
Turn on the LCD-TV  
When the POWER button is pressed and the LCD-TV is  
SLEEP DISPLAY MUTE POWER  
NICAM  
PC  
AUTO AD TV/AV  
turned on, the indicator light on the front of the LCD-TV  
changes from red to green. When the LCD-TV is turned on,  
the input mode is displayed on the screen. When the LCD-TV  
is turned off using the power button, the LCD-TV will go into  
standby mode and the indicator light turns red.  
PSM  
OK  
.SSM  
Q.VIEW  
P+  
Note:  
The display of the input mode  
will disappear in3 seconds.  
TV  
V-  
MENU  
V+  
P-  
SCART  
INDEX  
TEXT  
SUBCODE MIX  
PC-RGB  
AV  
TIME  
HOLD  
SIZE  
REVEAL  
S-VIDEO  
Switch Among Different Inputs: TV / SCART / PC-RGB / AV / S-VIDEO  
Press the TV/AV button to select the input mode you want.  
Each time you press the TV/AV button, TV, SCART , PC-RGB, AV, S-  
VIDEO, will appear on the screen in the order.  
.
Note:  
The display of the input mode will disappear in 3 seconds.  
Audio Control  
1.Press the V+ button to increase the volume. A number will appear on  
screen indicating the volume level.  
2.Press the V- button to decrease the volume. A number will appear on  
screen indicating the volume level.  
Mute  
1.Press the MUTE button to mute the sound temporarily. A mute icon  
appears on the screen.  
2.Press the MUTE button or V+ again to restore the sound.  
The mute icon disappears.  
Note: when you cut off the power supply completeley , the mute function is  
cancelled automatically . But if the TV is switched to standby mode , the  
mute function can not be cancelled.  
When you press MUTE to cancel the sound ,if you press V- button , the  
level of the sound will be decreased, but the sound is still mute. In this  
condition,when you press MUTE again, the sound will restore the level you  
have decrease just.  
 
Basic Operating Instructions  
Select the TV Channel You Want  
You can use the number keys on the remote control to directly select TV  
channels.  
The LCD-TV can store up to 100 channels , and you can press the keys on the  
remote control or on the panel to make a selection.  
1.Press the relevant key on the remote control if you want to choose any channel  
from 0 to 9. for example: if you want to choose channel 8, just press the key  
number 0 and 8.  
Note: You must press 0 first and then the other numbers from 0 to 9 if you want  
To choose channels from 0 to 9)  
2.If you want to choose a channel bigger than 9, please enter the two digits of the  
channel number you want to watch within 3 seconds. for example: select  
channel 16  
Picture Mode  
Press PSM button on the remote control for menu display . For desired mode as  
follows:  
PERSONAL STANDARD MILD FRESH  
 
TELETEXT  
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD  
control functions are not available in TELETEXT mode. If the TV is switched on by POWER  
after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will  
disappear automatically.  
Teletext features may vary depending on the Broadcasting  
Companies and is only available if the channel selected is  
SLEEP DISPLAY MUTE POWER  
NICAM  
PC  
AUTO AD TV/AV  
transmitting Teletext. Pressing the TEXT button whilst in  
Teletext operation will switch the current status to TV.  
When in Teletext mode, the volume may still be altered to  
the desired listening level.  
PSM  
OK  
.SSM  
Q.VIEW  
P+  
V-  
MENU  
V+  
Page Selection  
P-  
INDEX  
TEXT  
Pages can beselected in twoways:  
a. Press P+ or P- button to increase or decrease the  
page number by one.  
SUBCODE MIX  
TIME  
HOLD  
SIZE  
REVEAL  
b. By entering the page number, using the number  
keys on the remote control.  
SIZE Button  
Press SIZE button to change display size : normal large top large bottom  
normal  
REVEAL Button  
Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again  
to hide.  
Red/Green/ Yellow/CyanButtons  
These four buttonscorrespond to thedifferently colored subjects .  
HOLD Button  
Press HOLD button to remain the Teletext page when viewing multi-page  
information .  
INDEX Button  
Press INDEX button to return to the main index page .  
Depending on the way information is transmitted , this may have to be pressed  
more than once to return to the main index page .  
 
TELETEXT  
SUBCODE Button  
When Teletext information exceeds more than one page , it may take some time  
for the automatic changing of the sub pages to reach the sub page you require .  
It is possible to enter your required sub page and continue watching the normal  
programme until the correct sub page is found .  
Select the required page number using buttons 0-9 .  
If the top of the page indicates that sub pages are being transmitted yet the page  
does not change . Then the number at the top of the page is there to indicated  
that the broadcaster has updated the page s contents , there are no sub pages .  
Press SUBCODE button , page number/--- will be displayed at the bottom right  
of the screen.  
Enter desired sub page number before the page number/--- disappears . To  
select page 6 enter 0,0,0 and 6 .  
TEXT Button  
Press TEXT to enter Teletext mode and only the text page can be visible .  
MIX Button  
Press MIX button to enter Teletext mode and both the TV picture and text page  
can be visible.  
TIME  
While in normal TV mode only, pressing the button TIME will display the  
teletext time in the top right corner for a few seconds.  
 
Menu Operations  
* In this manual, the OSD (On Screen Display) may be different from your TV  
because it is just an example to help you with the TV operation.  
s
1. Press MENU button to either display the PC MENU or  
TV MENU or  
VIDEO MENU or GENERAL MENU or AUDIO MENU in different  
source inputs.  
2. Press P+/P- to scroll through the parameters  
3. Press V+/V- buttons to make changes to the parameters  
4. Press the OK button to exit the menu  
Picture Menu Options  
Picture quality can be adjusted for any input separately .  
The picture qualityon the screencan be adjustedas follows:  
1. Press MENU button until the following menu appears on the screen.  
PC MENU  
PC MENU  
BRIGHTNESS  
CONTRAST  
50  
50  
COLOR SETTING 9300K  
AUTO CONFIG  
H-POSITION  
V-POSITION  
PHASE  
50  
50  
50  
50  
CLOCK  
AV/S-VIDEO MENU  
VIDEO MENU  
BRIGHTNESS  
CONTRAST  
COLOR  
HUE  
SHARPNESS  
50  
50  
50  
50  
50  
 
Menu Operations  
Picture Menu Options Continued  
TV MENU  
VIDEO MENU  
BRIGHTNESS  
CONTRAST  
COLOR  
HUE  
SHARPNESS  
50  
50  
50  
50  
50  
2. Press P+/P- button to enter the picture menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference .  
4. Repeat step 2 and step 3 until desired picture quality has been achieved .  
Function:  
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it  
will add more light to dark parts of the picture and by decreasing the level ,it will  
add more dark to light parts of the picture.  
CONTRAST : Adjust the contrast of the picture . The image becomes higher as  
the number increase.  
COLOR SETTING : Press V+/V- to select between 9300K/6500K/USER  
define . You could adjust the color values in USER mode . And the menu display  
as follows:  
USER COLOR SETTING  
RED  
GREEN  
BLUE  
100  
100  
100  
AUTO CONFIG : Is opted for adjustment of picture location frequency and phase  
parameters .  
H-POSITION : Picture horizontal adjust  
V-POSITION : Picture vertical position adjust .  
 
Menu Operations  
Picture Menu Options Continued  
PHASE : Removes any horizontal distortion and clears or sharpness the displayed  
characters .  
CLOCK :Adjust the TFT-LCD tomatch the PC-RGBinput source  
COLOR : Press V+/V- to adjust the color  
HUE :Adjust the toneof the picture. Appearand be adjustedonly under NTSC  
mode  
SHARPNESS : Adjust the amount of the detail enhancement , the image  
sharpness rises as the number increases (By increasing the level, it will show  
cleaner and clearerimages and bydecreasing the level, it will makepicture  
smoother).  
Sound Menu Options  
Sound can be adjusted for any input as follows:  
1. Press MENU button until the following menu appears on the screen  
AUDIO MENU  
VOLUME  
BALANCE  
50  
50  
AUDIO PRESET PERSONAL  
TREBLE  
BASS  
AVL  
50  
50  
ON  
You can adjust sound options BALANCE, TREBLE, and BASS to the levels you  
prefer.  
2. Press P+/P- button to enter the audio menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to increase and decrease the level to adjust the  
selected option to your preference .  
4. Repeat step 2 and step 3 until desired audio quality has been achieved ..  
 
Menu Operations  
Sound Menu Options Continued  
Function :  
VOLUME : Adjust the volume of your TV  
BALANCE : Adjust the balance of the audio output from left to right . When  
indication value of balance increases toward 100 , sound of the left speaker  
becomes weaker . When indication value of balance decreases toward 0 ,  
sound of the right speaker become weaker .  
AUDIO PRESET : Press V+/V- to select between PERSONAL, VOICE,  
MUSIC and THEATER .  
TREBLE : Adjust the treble of the sound . Can only be adjust under PERSONAL  
mode .  
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .  
AVL: Select ON to adjust the volume level automatically.  
General Menu Options  
Menu Language Selection:  
The menus can be shown on the screen in the selected language. First select  
your language.  
1. Press the MENU button until the GENERAL MENU appears on the screen .  
2. Press P+/P- button to select LANGUAGE.  
3. Press V+/V- button to select your desired language.  
From this point on, the on-screen menus will be shown in the language of your  
choice.  
GENERAL MENU  
LANGUAGE  
ENGLISH  
ON  
OFF  
TV  
PAN EUROPEAN  
EAST  
BLUE SCREEN  
NOISE REDUCE  
INPUT SOURCE  
TXT LANGUAGE  
TXT EAST/WEST  
RESET  
 
Menu Operations  
General Menu Options Continued  
1. Press MENU button until the following menu appears on the screen  
GENERAL MENU  
LANGUAGE  
ENGLISH  
ON  
OFF  
TV  
PAN EUROPEAN  
EAST  
BLUE SCREEN  
NOISE REDUCE  
INPUT SOURCE  
TXT LANGUAGE  
TXT EAST/WEST  
RESET  
You can adjust sound options BLUE SCREEN , NOISE REDUCE, INPUT  
SOURCE and RESET to the levels you prefer.  
2. Press P+/P- button to enter the general menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to adjust the selected option to your preference .  
4. Repeat step 2 and step 3 until desired quality has been achieved ..  
Functions:  
1. BLUE SCREEN : You can set it ON or OFF . If select ON and there is no signal ,  
the screen will display blue screen  
2.NOISE REDUCE : select OFF/LOW/MID/HIGH to reduce the noise of the  
picture , provide clearer picture . (The effect is more and more distinctness if  
you select in sequence as follows: OFF, LOW, MID,HIGH.)  
3. INPUT SOURCE : Display current mode . There are PC-RGB , AV , S-VIDEO ,  
TV , SCART to display .  
4. TXT LANGUAGE: To switch the teletext languages.  
5. TXT EAST/WEST: To select EASTor WEST .  
6. RESET : Press V+ to reset some settings to the factory default .  
 
Menu Operations  
TV Menu Options  
1. Press MENU button until the following menu appears on the screen  
TV MENU  
CHANNEL  
SYSTEM  
SKIP  
AFC  
FINE TUNE  
SWAP  
1
DK  
OFF  
ON  
448.25MHz  
MANUAL SEARCH  
AUTO SEARCH  
Note: This menuis only appearsin TV mode.  
2. Press P+/P- button to enter the TV menu and to go up and down to  
select the desired option .  
3.Press V+/V- button to adjust the selected option to your preference .  
4. Repeat step 2 and step 3 until desired picture quality has been achieved ..  
Functions:  
1. CHANNEL : Press V+/V- to change the TV channel .  
2.SYSTEM : Select the TV standard system from DK,I,L,BG  
3. SKIP : If you want skip a channel , press V+/V- to select ON , and this  
channel will be skip next time when you press P+/P- . But you can press  
digits button to select the channel . If you want to restore the channel , select  
OFF.  
4. AFC : Auto frequence control . Select ON to improve the image quality .  
5. FINE TUNE : If the image received is not very good , you can press P+/P-  
to select FINE TURN item in menu . Then , press V+/V- button to adjust  
and improve the image quality .  
 
Menu Operations  
TV Menu Options Continued  
6. SWAP : Press V+ to display the menu as follows:  
FROM :  
TO :  
1
9
SWAP  
Press P+/- to select the item and then V+/- to adjust the channel and V+  
to confirm.( For example: press P+/- to select FROM item, and then press  
V+/- to adjust the channel number to 1; then Press P+/- to select TO item,  
and V+/- to adjust the channel number to 9; press P+/- to select SWAP item,  
and then V+ to confirm. The two channels will be exchanged)  
7. MANUAL SEARCH : Press V+ to start to search the channel . The following  
menu will display on the screen:  
DOWN  
543.25MHz  
UP  
Press P+/- or V+/- to select DOWN or UP , and then press MENU to confirm.  
(If you select DOWN, the search will search the lower frequency channel and UP  
will search the higher frequency channel)  
7. AUTO SEARCH : Auto search and save the channel .press V+ to start to  
search the channel and the following menu will appears on the screen :  
AUTO SEARCH  
SECAM L  
NO  
YES  
Press P+/- to select SECAM L , and V+/- to adjust between SECAM L and  
BG/DK/I system.  
Press P+/- to select NO or YES, and MENU to confirm. Then the TV will start  
to search as follows:  
AUTO SEARCH  
PLEASE WAIT  
11  
190.65MHz  
You could press MENU to stop the search .  
 
Specifications  
Specifications of the television that you have just purchased may  
vary from the information in this table due to technical innovations.  
Picture, sound  
PAL/SECAM-B/G,I,D/K,L,L  
system  
Antenna input  
impedance  
75  
Audio output  
1.5W+1.5W  
AV input PC input S-VIDEO input PC audio input  
SCART input 12V DC input Antenna input  
External input port  
Input: ~100-240V 50/60Hz,  
Output:  
--- 12V  
AC-DC adapter  
Temperature  
Working:5 C~35 C  
Storage:-15 C~45 C  
NOTE:Sound system L' certainly does not demonstrate in the TV's OSD, in  
menu L includes sound system L and sound system L'.  
Accessories  
1
2
AC-DC adapter  
AC cable  
3
4
Remote control  
Owner's Manual  
5 Batteries  
Warranty card  
6
Note Warranty card is only forthe special countriesand areas  
Note:  
All specifications are subject to change without notice.  
All quality are approximate value.  
 
V0.2  
0090506259  
 

Graco Camping Equipment 334644A User Manual
Graco Home Theater Screen 312759R User Manual
Grindmaster Coffeemaker AM 344 04 User Manual
Groupe SEB USA T FAL Iron FV6050 User Manual
Hasbro Games 13744 User Manual
Hasbro Robotics 81327 User Manual
Hawking Technology Network Router Wireless G Router User Manual
Honeywell Door RCW25 User Manual
Hotpoint Refrigerator 6BCR User Manual
HP Hewlett Packard Speaker 4275A User Manual