Haier Washer Dryer HWM120 CS User Manual

Twin-tub Washing Machine  
User's manual  
This manual is for  
HWM120-AS  
HWM120-BS  
HWM120-CS  
Please read this manual  
carefully before using.  
 
Retain it for future reference.  
Names of the parts  
Outer cover of the spin tub  
Inner cover of the spin tub  
Spin timer  
Drain selector  
Wash selector  
Wash timer  
Water-filling entrance  
Spin tub frame  
Spin tub  
water-filling translation  
Control panel  
Cabinet  
Bypass channel  
Water level adjusting lever  
Overflow filter  
Lint filter  
Drain hose  
Cabinet handle  
Pulsator  
Valve cover  
Wash tub  
Base frame  
Notes: All illustrations in this Manual are given for reference only. Your products and  
accessories may show differences from these illustrations due to our  
continuous improvement.  
Meaning and description of the symbols  
Contents marked with that symbol are related  
Warning sign  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage of the machine or injure the  
personal safety of the user.  
Contents marked with that symbol are actions  
Forbidding sign  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of the user.  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
1
 
Safety precautions  
When the machine is normally  
Please insert the power cord into  
special receptacle with rated vol-  
tage. Be sure to use single-phase  
three pins receptacle. The earthing  
terminal of the receptacle must be  
earthed reliably. If possible, please  
adopt electric leakage protector.  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned or when it  
is idle.  
If the power cord is bad, to avoid risk it is required to replace it by the  
technicians of our special shop or the after-sale service department.  
Keep the pin of the power plug clean.  
Do not put the machine at damp  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
Do not use water hotter than 50 C .  
In case the washing machine is installed  
on ground with carpet , do not block the  
ventilation hole with carpet.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
 
Safety precautions  
Do not decompose, repair or alter the  
machine by yourself.  
Do not stretch hands into the working  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Do not put any hot or heavy items Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
( such as the kettle with hot water )  
on the washing machine.  
Petrol  
inner  
Th  
Handicapped or children without care  
shall not use the machine.  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
To protect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
Please check if the water faucet is open,  
and if the connection of the water inlet  
pipe is proper.  
It is suggested to use foamless washing  
powder.  
3
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of  
the manual. It is very important to your security and correct operating  
the machine.  
Install the lint filter  
Put the underside of the lint filter into overflow filter  
then push the upside into overflow filter  
overflow filter  
lint filter  
After installation, please refer that the lint filter  
installed to the right station, otherwise the lint  
filter may be fallen off when washing, influencing  
your use.  
Usage of the drain hose  
The drainage shall be smooth with the drain hose.  
1.The height of the drain hose shall be  
less than 10 cm , or the drainage will  
not be smooth enough and cause  
incomplete drainage.  
<10cm  
2.Do not tramp or press the drain hose.  
3.If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
4.If extra drain hose is needed , please make  
separate purchase. The inner diameter of the  
extra hose shall not less than 40mm, and the  
>
40mm  
length shall not exceed 1.5m.  
<1.5m  
If the extra hose is too long, cut it either  
at point A or B.  
A
B
4
 
How to change the direction of the drain hoses  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
Back  
Figure 1  
Extend the drain hose from the side of spin tub  
Front  
Put soft items on the ground. Lean the machine  
down gently with the front surface facing the  
ground. Take off the drain hose from the cabinet.  
Take the hose out of the fixing groove.  
(See to Figure 2).  
Soft item  
Embed the drain hose into the groove  
along the side of the spin tub in the order  
of (1)~(3), heading for the side of the  
spin tub. (See to Figure 3).  
Figure 2  
Embed the drain hose into the  
groove with hands. Take care not  
to damage the drain hose in  
fastening the fixing clamp.  
Figure 3  
Embed into the  
groove in turn  
Extend to the  
spin tub side  
Install the water inlet hose; Select the water level  
Insert the water inlet hose into the water-filling  
entrance on the control panel  
To dismantle the water inlet pipe,  
just push the control handle as indicated in the  
figure and pull it out  
Water inlet hose  
Water level  
indicator  
Water inlet  
Maximum  
Max  
Select water level according to the  
quantity of the laundries.  
Med  
Medium  
Min  
Set the water level adjusting lever  
Minimum  
to needed line.  
5
 
Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
Pay attention to followings before washing the laundries  
Check if  
The quantity of  
When the pulsator  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
the laundries is running , the  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
6
 
The musts in washing  
The capacity of washing and spinning of the  
machine refer to the largest weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time. Laundries  
quantity in one washing cycle shall be lower  
than the rated capacity.  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
Do not select " Maximum " water level for  
few laundries , so as to avoid splashing of water.  
It is suggested not to use high sudsingdetergent.  
Usage of the detergent  
How to use the whitener  
How to use the washing powder  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30  
seconds to dissolve it completely.  
3.Put it in the laundries. Select suitable  
water level.  
Fill water to decided level. Dilute  
the whitener with container.  
Pour it slowly into thewashing tub.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 C and a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
7
 
Washing sequence  
Intensity seleciton  
Spin timer  
Wash timer  
(If to set less than 2 min,  
Drain switch  
If to set less than 1 min, in  
order to ensure long service life,  
please first surpass 2 min and  
then turn back  
Intensity can be standard,  
you should first surpass 6 min or soft)  
and then turn back.)  
Do not set drain switch  
on Drain position during  
washing)  
OFF  
STANDARD  
OFF  
OFF  
SOFT  
5
15  
3
1
DRAIN  
12  
6
4
2
3
9
WASH TIMER  
WASH SELECTOR  
DRAIN SELECTOR  
SPIN TIMER  
Wash  
1
Fill selection  
(1) Set fill selection to Wash side  
.
Figure 1  
SPIN  
Figure 1  
Figure 2  
ET SELOR  
WASH  
(2 )Adjust water level rod to a position as needed.  
2
Fill water and add solved powder detergent until  
water reaches a suitable level.  
It begin to wash to dispense detergent uniformly.  
STANDARD  
SOFT  
Page 7  
3
4
Put in the wash load, and supplement water  
as necessary.  
WASH SELECTOR  
Figure 3  
OFF  
15  
3
Select intensity  
Select Normal, intense or Jeans water flow  
6
intensity according to wash load.  
Figure 3  
9
WASH TIMER  
Figure 4  
5
6
Select wash time  
OFF  
Figure 4  
Select wash time according to wash load.  
DRAIN  
After completion of wash, please set drain  
switch at Drain position.  
(Figure 5)  
DRAIN SELECTOR  
Figure 5  
8
 
Midway spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
Please put in the gland properly even if the  
laundries quantity is small.  
Push  
Gland  
Push  
Proper  
The laundries  
are slanting  
Proper  
No gland  
(2) Close the inner and outer cover of the spin tub.  
Outer cover of  
The spin tub  
Inner cover of  
The spin tub  
(3) Spin for 1-2 minutes.  
3.Run the foam-removing spinning.  
1
Set the fill selector handle on spin side and  
Water inlet  
Fill selector handle  
fill water for about 1 min.  
In case water flows out from wash tub side  
due to too much inflow, please turn down  
the water tap a bit.  
INLESELECOR  
WASH  
SPIN  
2
Close the spin tub outer cover and spin  
for about 1 - 2 min.  
9
 
Rinsing  
Rinse with water-filing  
OVERFILL  
1.Put the laundries into the wash tub. Select  
suitable current according to the laundries.  
If you find water flo-  
wing out here,please  
twist the water tap to  
limit the water filling.  
2.Adjust the water level  
Set the water level with water level adjusting  
lever according to the laundries quantity.  
Then fill suitable water continuously.  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do  
rinsing.  
(Repeat the midway spinning and  
Rinse with stored water rinsing with stored water for 2-3 times)  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is few, please use "Soft" current.  
If you use "Standard" current, it may splash.  
10  
 
Spinning  
1. Put the laundries into the spin tub  
evenly and smoothly.  
2. Press the gland in the tub properly.  
Close the inner and outer cover of  
the spin tub.  
3. Spin  
Select suitable spin time according  
to the laundries, and do spinning.  
During spinning, if there's abnormal  
sound, it is generally owing to slanting  
placement of the laundries. Please  
stop the machine and re-order the  
laundries.  
In spinning, it will pause the work if you open the outer cover of the spin  
tub. Close it to resume the spinning.  
To do spinning and draining  
or rinsing with water-filling  
together, please first do  
spinning for around 1 minute,  
then do draining or rinsing  
with water-filling. Otherwise  
the spinning will stop owing  
to too much water stored in  
the spin tub.  
11  
 
Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Press the elastic piece at upper end of lint filter to  
release the tab from the filter cover, and pull the lint  
filter outward to remove it. (See Figure 1).  
Figure 1  
2. Remove lint  
Pull the lower end of lint filter rear cover outward  
to disassemble it from the lint filter front cover.  
Remove lint completely with clear water. (See  
Figure 2).  
Lint filter rear cover  
Disassemble  
Assemble  
Lint filter frontcover  
3. Install lint filter  
Page 4  
Figure 2  
Cleaning the overflow filter  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
Elastic fixing  
claw  
1
Take off the overflow filter.  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
12  
 
Cleaning the overflow filter  
2. Take off the corrugation pipe.  
Dismantle the upper part of the  
corrugation pipe inside the  
overflow filter ( as indicated in  
Figure 1).  
Water level  
adjusting lever  
Corrugation  
pipe  
3. Cleaning the overflow filter  
Clean the lint around the filter  
and flush with tap water.  
Figure 1  
4. Install the overflow filter.  
(1).Install the corrugation pipe.  
(2).Insert the mounting plate at  
the bottom of the filter into  
the valve cover.  
Hook  
(3).Hang up the hook at the left  
upper side.  
(4).Push the upper part in as  
indicated in Figure 2.  
Figure 2  
Disposal of the complete unit  
After washing, dismount the water inlet  
hose.  
Do not store water in the tub for long  
period. Discharge the water immediately  
after each using.  
Pull off the power plug and hang up the  
power cord.  
Hang up the drain hose.  
Wipe the complete unit with soft  
cloth twisted dry.  
Wipe with neutral detergent if too dirty  
Do not wash it directly by water  
Wipe off the water drops on the surface  
and inside the tub with clean soft cloth.  
Open the cover of the wash tub and the  
inner/outer cover of the spin tub for  
some time (about one hour), then close  
them.  
Petrol  
Thinner  
Alcohol  
13  
 
Trouble-shooting Answers to question  
When the remained water is frozen  
Prevent the freezing (be sure to discharge the water  
completely after using)  
After complete draining, set the "DRAIN SELECTOR"  
at "OFF" . If it is set at "DRAIN", it will be rather  
Below 50  
2~3L  
difficult for the frozen water to melt.  
When the water is frozen  
Pour hot water below 50  
into the wash tub  
to soak it completely. Then turn the pulsator  
with hands gently. Please confirm the drainage  
can work normally before next using.  
14  
 
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by foreign materials?  
The machine does  
not act.  
Is the drain hose put down?  
Is the drain hose frozen?  
Is the drain hose blocked by foreign material?  
Are there laundries falling to the outer side of  
the spin tub?  
The draining does  
not work  
There's abnormal  
sound during washing  
Are there hair pin, coins or metal items brought  
inside the tub?  
Is the machine slanting?  
There's abnormal  
sound and violent  
vibration during  
spinning  
Is the gland pressed evenly?  
Are there laundries falling to the outer side of  
the spin tub?  
Are the laundries in spin tub too much?  
There may be some  
waterflowing out of  
the drain hose in the  
first use of the  
It is the water remained in the factory inspection  
of performance.  
machine.  
15  
 
Packing list  
Quantity  
One piece  
Name  
User's manual  
Water inlet hose  
One piece  
One piece  
One set  
Gland  
Twin-tub washing machine  
Specification  
Water level Water quantity about (L)  
Rated washing capacity(kg)  
Rated spinning capacity(kg)  
Maximum/99 Medium/79 Minimum/59  
12.0  
7.0  
Injection pressure(MPa)  
0.02~0.2  
16  
 

Haier Refrigerator COMPACT REFRIGERATOR User Manual
HannsG Computer Monitor HSG1078 User Manual
Harbor Freight Tools Welding System 66787 User Manual
Hasbro Motorized Toy Car 08645 06580 User Manual
Hoshizaki Refrigerator KML 250MAH User Manual
Hotpoint Washer 9537 User Manual
HP Hewlett Packard Computer Monitor 705 User Manual
HP Hewlett Packard Laptop WZ226UT#ABA User Manual
Hunter Fan Fan 22787 User Manual
Hyundai Car Video System H CMMD4040 User Manual